When used indoors, it is able to work through walls and furniture. The RF remote can work up to 80 feet in an open area. You can also mount multiple wall switches to any convenient spot, and never worry about losing the remote controls. With this remote light switch, you can control lights, electronics, or small appliances in hard-to-reach areas. The Fosmon wireless switch allows you to easily upgrade your standard outlet to a remote controlled outlet. Join millions of satisfied customers with our limited lifetime warranty, backed by our experienced and dedicated USA based customer service. It is compatible with LED, CFL, and incandescent. The wireless plug is rated 125V/15A 1875W general purpose, 1250W Tungsten, and ½ HP. The safety and quality of the wireless remote plug is ETL certified, and the 3-prong grounded outlet provides an extra protection. The wall switch is lightweight and sturdy, and comes with mounting hardware and a battery. The low profile construction makes it easy fit behind furniture or in hard-to-reach areas. Unlike other bulky remote plugs that either only fit one piece or occupy both receptacles in a duplex outlet, the Fosmon wireless plug can fit one or two plugs in a duplex outlet. The Braille on the switch makes it user-friendly for visually impaired people. ![]() The RF remote woks through walls or furniture without line-of-sight. You can set up multiple switches for one outlet or one switch for multiple outlets, making it easy to implement a single pole, 3-way, or multi-way switches – perfect for hallways, stairways, basements, or garages. The wall switch remote is able to pair with the outlet plug in any combination you need. It is perfect for lighting, electronics, or small appliances. By simply plugging the receiver to an outlet and mounting the switch on the wall or using it as a hand-held remote, you can turn the outlet on and off with a simple click. This does not allow the radio sufficient time to initialize before starting the booting process.Fosmon’s wireless outlet switch allows you to add a wall switch to your light or fan without electrical wiring or hiring an electrician. Using the front panel power switch is the same as using the Digital Loggers switch to boot up and shut down the radio, so you are essentially substituting a power button press for the Digital Loggers switch closure and switch opening.ĬAUTION: We recommend that you do not use a web-controlled AC switch to power on and off the power supply while using a grounded RCA male plug inserted into the REM ON connector and the REM ON connector enabled. The total time is 2 minutes.Ģ.) Now I turn off the DC power supply using the web-controlled AC switch. Now, wait one additional minute for the PSoC to shut down its connected systems. About 1 minute later the radio should be shut down. About 1 minute later the radio should be completely booted upġ.) I open the Digital Loggers switch which starts the radio boot shutdown process. This device can be purchased directly from FlexRadio: FlexRadio Approved Remote On Plug and Play Kitġ.) Turn on the DC power supply using the web-controlled AC switch and wait two minutes to ensure the PSoC processor has completely initialized.Ģ.) Now close the Digital Loggers switch which starts the radio boot-up process. An example would be the Digital Loggers Enclosed Power Relay ( ) ![]() This is the control used to boot and shut down the radio during normal operating conditions. The second is a web-controlled Digital Loggers contact switch that is connected to the REM ON connector on the radio. An example of this would be the Digital Loggers Pro Switch ( ) This is essentially a "kill switch" if anything goes wrong and you need to shut down the radio quickly and completely. ![]() The first is a web-controlled AC switch that is connected to the 13.8 VDC supply. Use two (2) remote-controlled switches for powering the radio. ![]() Here is the "best practice" method for shutting down a FLEX-6000 remotely. NOTE: To use this remote power-on feature, you have to ENABLE the REM ON option in the Settings->Radio Setup->Radio tab. The FLEX-6000 Signature Series SDRs have a connector, REM ON (REMote ON), that will allow you to start or boot the radio using a contact-to-ground connection if the radio has power applied to it. The ability to turn on or off your radio while operating remotely is a necessary convenience when using SmartLink.
0 Comments
Leave a Reply. |